Structural Analysis Lab Apparatus

Product Details:

Specification:

• The set up should consist of cylindrical test section filled with porous medium. Pressure tapping provided in the test section to measure the pressure drop with help of differential manometer control valves are fitted in the water line to regulate flow of water in the section. It should be self–contained water re-circulating unit provided with a sump tank and a centrifugal pump etc. Flow control valve and pass valve are fitted in water line to conduct the experiment different flow rates. Flow rate of water is measured with the help of measuring tank and stop water.

Experimentation:

• To Verify Darcy’s Law.
• To Find Out The Coefficient Permeability Of A Given Medium.

Utilities Required:

• Water Supply
• Drain

Technical Details:

• Water Circulation: FHP Pump.
• Flow Measurement: Using Rota Meter
• Sump Tank: Made Of Stainless Steel, Compatible Capacity
• Stop Watch: Mechanical Type, 0.2 Sec. Resolution
• Control Panel Comprise Of Speed Control Unit, Standard Make On/Off Starter, Mains Indicator, Fuse Etc.
• Tank Will Be Made Up of Stainless Steel.
• The Whole Set- Up Is Well Design And Arranged In Good Quality Painted Structure.

Product Details:

Centerefugal pump are dynamic pressure pumps. This is a self-contained recirulation type unit all the measurement are provided to evaluate the performencee of the pump.

Specifications:

• Pressure Guage for measurement discharge head.
• Control Valve to calculate input power.

Range of Experiment:

• To determine the efficiency of pump.
• To study the following characteristics on different RPM.
• Discharge V/s Speed
• Discharge V/s Total head
• Discharge V/s Input power
• Discharge V/s Output power
• Discharge V/s Efficiency of pump
• Discharge V/s Overall efficiency

Product Details:

This is a reaction turbine and this test rig shows the construction and working of Kaplan turbine. Rope brake dynamometer is used to measure the output of turbine. Pressure gauge and orifice meter are used to measure the input of turbine.

Specifications:

• This Francis Turbine Test Rig 100mm size to develop 2 HP at 1250 RPM with a flow o( about 1400 Ipm at 15 meters supply head Supply pump set lOOxlOOmm size, 1500 Ipm at 15 meter head suitable for supplying water to the above turbine.
• Sump Tank :MS Tank to store sufficient water for independent circulation through the unit experimentation and arrange within the floor space of main unit. Capacity 650 ltr.
• Rope Bake Dynamometer is used to measure the output. Spring balance and dead weights are used to measure the load Runner Diameter 220mm.
• Discharge control valve used to control the flow rate of water.
• Spring Balance 6 Kg (Salter Make)
• Pressure Gauge of 4.2 kg/cm2 is used to measure the pressure head.
• Rigid MS frame work compactly fitted with all the above items as a self-sufficient
• Package unit suitable for operation without any foundation.
• Switch and starter suitable for above motor pump set mounted on the control panel board

Experimental Capabilities:

• To determine the efficiency of Turbine
• To draw the characteristics curve of Turbine

Product Details:

Description:

• The apparatus has been designed to illustrate the basic features of electrical resistance strain gauges and their application to measurement of strain and the derivation of stress levels, in bending, torsion, tension and compression.
• An alloy cantilever has a single gauge bonded onto its surface, and an identical gauge is fixed to an unstressed piece of the same material for temperature compensation. The two gauges form part of a Wheatstone Bridge which has an apex or balancing potentiometer, and whose meter is calibrated directly in microstrains. The cantilever is loaded by weights hung from its free end, a weight hanger is included.
• To extend the scope of the apparatus the cantilever can be replaced by a torsion bar having two gauges bonded orthogonally at 45º
• For a complete study of strain gauging two optional extra accessories demonstrate averaging techniques for tension and compression specimens.
• This equipment is part of a range designed to both demonstrate and experimentally confirm basic engineering principles. Great care has been given to each item so as to provide wide experimental scope without unduly complicating or compromising the design. Each piece of apparatus is self-contained and compact. Setting up time is minimal, and all measurements are made with the simplest possible instrumentation, so that the student involvement is purely with the engineering principles being taught.
• A complete instruction manual is provided describing the apparatus, its application, experimental procedure and typical test results.

Features:

• Low cost effective teaching
• Bench mounted
• Self contained
• Wheatstone bridge and temperature compensation dummy gauge included
• Introduction to strain gauges
• Bending and Torsion included
• Optional extras for Tension and
• Compression
• Three year warranty

Range of Experiments:

• To show the application of strain gauges in the measurement of stress, due to bending and torsionTo demonstrate the use of a Wheatstone Bridge in measuring change of resistance.With the optional extras to show other methods of temperature compensation in conjunction with tension and compression specimens.

Product Details:

In our extensive range of products, we offer our esteemed clients a broad array of high quality Redundant Joint Apparatus.

Specifications:

• Apparatus should consists of three suspension members (spring balances) of different stiffness which are jointed at a point to form the redundant joint. The upper end of the suspension members being tied in a position to a vertical wooden board. Arrangement is provided to apply a vertical load at the joint and to measure its horizontal and vertical displacement on a paper and also elongations and forces in the suspension members by the help of dial gauges. Two dial gauges with 25mm travel (with magnetic bases) are supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights.

Product Details:

Specifications:

• Transparent Hele Shaw Apparatus.
• Suitable stand.
• Two dimensional models of cylinder, aerofoil, Square & triangular.
• Measuring cylinder

 

Services Required:

• A small bucket may be sufficient which can be emptied once it is filled.
• Suitable drainage arrangements.

Product Details:

This unit shows the construction and working of Pelton Wheel Turbine It consists of pelton wheel rotate by the jet of water supplied from centrifugal pump. Rope break dynamometer is used to measure the output of turbine. Pressure Gauge and Orifice meter are used to measure the input of turbine.

Sump Tank:

• MS Tank to store sufficient water for independent circulation through the unit experimentation and arrange within the floor space of main unit. Capacity 650 Ltr.
• Runner coupled to pelton wheel. Rope Bake Dynamometer is used to measure the output Runner diameter 220mm.
• Spring Balance 6 kg (Salter Make).
• Discharge Butter Fly valve used to control the flow-rate of water.
• Pressure Gauge of 4.2 kg/crn² is used to measure the pressure head.
• Rigid MS frame work compactly fitted with all the above items as a self-sufficient
• package unit suitable for operation without any foundation
• Switch and starter suitable for above motor pump set mounted on the control panel board

 

Experimental Capabilities

• To determine the efficiency of Turbine
• To draw the characteristics curve of Turbine

Product Details:

This is a reaction turbine and this test rig shows the construction and working of Francis turbine. Rope brake dynamometer is used to measure the output of turbine. Pressure gauge and orifice meter are used to measure the input of turbine.

Specifications:

• Supply pump set lOOxlOOmm size, 1500 Ipm at 15 meter head suitable for supplying water to the above turbine.
• Sump Tank :MS Tank to store sufficient water for independent circulation through the unit experimentation and arrange Within the floor space of main unit. Capacity 650 Itr.
• Rope Bake Dynamometer is used to measure the output.
• Spring balance and dead weights are used to measure the load.
• Runner Diameter 220mm.
• Discharge Butter Fly valve used to control the flow rate of water.
• Spring Balance 6 Kg (Salter Make)
• Rigid MS frame work compactly fitted with all the above items as a self-sufficient package unit suitable for operation without any foundation.
• Switch and starter suitable for above motor pump set mounted on the control panel board.

Experimental Capabilities:

• To determine the efficiency of Turbine
• To draw the characteristics curve of Turbine

Product Details:

Our precious clients can avail from us an exclusive array of Three Hinged Arch Apparatus.

Specifications:

• The mild steel model should have a span of 100cm and rise 25cm, with hinges at supports and crown. One of the ends should rests on rollers. Along the horizontal span of the arch various points are marked at equidistant for the application of load. This being a statically determinate structure, the horizontal thrust developed under the action of any load system can be theoretically calculated and will also be measured directly by neutralizing the outward movement of the roller end. A dial gauge with 25mm travel (with magnetic base) may be supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights.

Product Details:

We are one of the leading manufacturers, suppliers and exporters of Unsymmetrical Bending Apparatus.

Specifications:

• Apparatus should consist of a mild steel angle of size 1" x 1" x 1/8" or in equivalent metric units of length 80cm is tied as a cantilever beam. The beam should be fixed at one end such that the rotation of 450 intervals can be given and clamped such that the principal axis of its cross-section may be inclined at any angle with the horizontal and vertical planes. Also arrangement may be provided to apply vertical load at the free end of the cantilever and to measure horizontal and vertical deflection of the free end. A dial gauge with 25mm travel (with magnetic base) should be supplied with the apparatus. Apparatus should be supplied complete with a supporting stand and a set of weights.

Product Details:

We offer optimum quality of Deflected Beam Apparatus.

Specification:

• Apparatus should of consists of a mild steel beam 2.5cm x 3mm in cross section and 100cm long, pinned to two supports 70cm apart situated symmetrically. One of the ends can be fixed or given a known slope by applying a known moment at the end with the help of suspended loads. At the other end also a known moment can be applied. Vertical loads can be applied at various points along the span of the beam. A dial gauge with 25mm travel (with a magnetic base) may be supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights.

Product Details:

We have range of high quality of Two Hinged Arch Apparatus.

Specifications:

• The model should have a span of 100cm and rise 25cm. Both ends should have hinge but one of the ends should also be free to move longitudinally. A lever arrangement may be fitted at this end for the application of known horizontal inward force for measuring the horizontal thrust. Along the horizontal span of the arch various points are marked at equidistant for the application of load. This being a statically indeterminate structure of the first degree. A dial gauge with 25mm travel (with magnetic base) should be supplied with the apparatus. Mild steel apparatus supplied should be complete with a supporting stand and a set of weights.

Product Details:

Owing to the industrial experience in this domain, we have been to offer optimum quality Elastically Coupled Beam Apparatus.

Specification:

• Apparatus should of consists of a three parallel bar suspension system with elastic beam at their upper and lower ends. The upper ends of the two outer suspension rods are tied to a vertical wooden board while central suspension rod may be tied to the center of another elastic beam supported at two outer ends only. Mild steel Apparatus to be supplied should be complete with a supporting stand and a set of weights.

Product Details:

Apparatus consists of four spring steel columns which are put along a vertical wooden board.

These four columns have different end conditions as below:

• Both ends pinned
• Both ends fixed
• One end pinned and other fixed
• One end fixed and other end free
• Apparatus supplied is complete with a supporting stand and a set of weights

Product Details:

The model have a span of 100cm and rise 25cm. Both ends should have hinge but one of the ends should also be free to move longitudinally. A lever arrangement may be fitted at this end for the application of known horizontal inward force for measuring the horizontal thrust. Along the horizontal span of the arch various points are marked at equidistant for the application of load. This being a statically indeterminate structure of the first degree. A dial gauge with 25mm travel (with magnetic base) should be supplied with the apparatus. Mild steel apparatus is complete with a supporting stand and a set of weights.

Additional Information:

• Item Code: NIC-41
• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: ROORKEE

Product Details:

We are engaged in offering a wide range of Column and Struts Apparatus.

Specification:
Apparatus should consists of four spring steel columns which are put along a vertical wooden board.

These four columns have different end conditions as below:

• Both ends pinned
• Both ends fixed
• One end pinned and other fixed
• One end fixed and other end free

Apparatus to be supplied should be complete with a supporting stand and a set of weights

Additional Information:

• Item Code: NIC-42
• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: ROORKEE

Product Details:

Apparatus for Verification of Clarkes Maxwell Reciprocal Theorem

Specifications:

• Apparatus should consists of a mild steel beam 100cm long and 1.25cm x 4mm in cross section with graduations at every 10cm along the length. It should be supported on two knife edge supports 70cm apart with a 30cm overhang on one side. Reciprocal theorem can be verified by direct measurements of the deflections of various points with the help of a dial gauge due to a load placed at the reciprocal points. A dial gauge with 25mm travel (with a magnetic base) should be supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights.

Additional Information:

• Item Code: NIC-43
• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: ROORKEE

Product Details:

We offer optimum quality of Deflected Beam Apparatus. Apparatus should of consists of a mild steel beam 2.5cm x 3mm in cross section and 100cm long, pinned to two supports 70cm apart situated symmetrically. One of the ends can be fixed or given a known slope by applying a known moment at the end with the help of suspended loads. At the other end also a known moment can be applied. Vertical loads can be applied at various points along the span of the beam. A dial gauge with 25mm travel (with a magnetic base) may be supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights.

Additional Information:

• Item Code: NIC-45
• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: ROORKEE

Product Details:

Our clients can avail from us a comprehensive range of Deflection of Truss Apparatus.

Specification:

• Apparatus should consist of 4 panels of a PRATT steel truss, each panel being 40cm in horizontal direction and 30cm in vertical direction. Load can be applied on each panel point. All tension members should be provided with detachable springs so as to obtain appreciable deformation of the member. Direction of the diagonal members may be changed. Apparatus can be used to illustrate visually the nature of forces set up in various members of the Truss. Apparatus to be supplied should be complete with a supporting stand and a set of weights.

Additional Information:

• Item Code: NIC-47
• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: ROORKEE

Product Details:

We are one of the leading manufacturers, suppliers and exporters of Unsymmetrical Bending Apparatus.

Specifications:

• Apparatus should be supplied complete with a supporting stand and a set of weights.

Product Details:

Elastic Displacements (Vertical Horizontal) of curved members Apparatus consists of a steel bar which is used to make the different cur members Viz. circle, semicircle with straight arm, a quadrant of a circle and quadrant of a circle with straight arm. The bottom ends of the members are fixed to the base. Under the application of load at free end, its horizontal and vertical deflection is measured with the help of dial gauges.A dial gauge with 25mm travel (with a magnetic base) is supplied with the apparatus Elastic Displacements (Vertical Horizontal) of curved members Apparatus consists of a steel bar which is used to make the different cur members Viz. circle, semicircle with straight arm, a quadrant of a circle and quadrant of a circle with straight arm. The bottom ends of the members are fixed to the base. Under the application of load at free end, its horizontal and vertical deflection is measured with the help of dial gauges.

A dial gauge with 25mm travel (with a magnetic base) is supplied with the apparatus

Product Details:

This demonstration unit facilitates the experimental investigation of the progression of the bending moment and shearing forces on a bar subject to point loads. In addition, the section principle commonly used in mechanics can be demonstrated. Due to the use of a low friction joint with two degrees of freedom at 1/3 of the span and two dynamometers, the measurements can be recorded directly from the bar. The deflection of the bar as result of the travel of the dynamometers and the horizontal alignment can be compensated and regulated using two adjustment bolts. The bar is loaded with graduated sets of weights that can be attached at any point on the bar

Additional Information:

• Item Code: NIC-50
• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: ROORKEE

Product Details:

We are engaged in offering a wide range of Column and Struts Apparatus.Apparatus to be supplied should be complete with a supporting stand and a set of weights.

Specification:

• Apparatus should consists of four spring steel columns which are put along a vertical wooden board.

These four columns have different end conditions as below:

• Both ends pinned
• Both ends fixed
• One end pinned and other fixed
• One end fixed and other end free

Product Details:

Two identical pumps operated in parallel approximately double the discharge while preserving the same head. Likewise, when two identical pumps should connected in series. The discharge rate should be same as that from one pump but the head is approximately doubled. It is often more economical to for two pumps in series or parallel operation rather then a single larger one which may be underutilized for much of the time. In the former arrangement one pump may be switched off when demand is low, thereby operating at the higher efficiency and also enabling maintenance to be done on the idle unit.

 

Technical Specifications:

• Measurement Tank or Rota meter: To measure discharge .
• Energy meter: To measure electrical input.
• Pressure and vacuum gauges - one each for each pump.
• Digital speed indicator - 2 nos.
• Sump Tank of suitable capacity.
• Necessary piping and valves for series and parallel operation of the pumps.

Experiments to Perform:

• Performance evaluation of individual pumps.
• Study of performance of pump in series and parallel combinations.

Manual:

• A manual is to be supplied which gives details of the apparatus and procedure of experiments.